Stereo Audio Breakout Board
Introduction Stereo Audio Breakout Board:
TRRS connectors are the audio-style connectors that you see on some phones, MP3 players and development boards. TRRS stands for “Tip, Ring, Ring, Sleeve,” which reflects the fact that, unlike a standard stereo connector, this actually has three conductors and a ground. Some devices use the extra conductor for a microphone (like hands-free headsets) or to carry a video signal (like in some MP3/MP4 players). This breakout board makes it easy to add a TRRS jack to your prototype or project by breaking out each conductor to a standard.
The I2S Audio Breakout board uses the MAX98357A digital to analog converter (DAC), which converts I2S (not be confused with I2C) audio to an analog signal to drive speakers. The MAX98357A has a built in class D amplifier which can deliver up to 3.2W of power into a 4Ω load. For more information, see the Hardware Overview section below.In addition to being able to select the audio channel output, the gain can also be configured in a few ways. The gain of the amplifier can be configured from as low as +3dB to as high as +15dB. While the channel selection can be configured on board, the gain however is controlled externally using the gain pin. By default, the board isconfigured for +9dB, but can be changed using the table below.
Spceifications:
-
Connector type: 3.5v
-
Adapter PCB Size: 1.5v
-
Header Pin Pitch: 2.54A
-
dapter PCB Thickness: 1.6V
-
Module Maximum Height: 6.75A
Circuit Operation:
A TRRS or Tip Ring Ring Sleeve plug has four conductors and is very popular with 3.5mm, and can be used with stereo unbalanced audio with video or with stereo unbalanced audio plus a mono microphone conductor.Unlike a standard stereo connector, this actually has three conductors and a ground. Some devices use the extra conductor for a microphone (like hands-free headsets) or to carry a video signal (like in some MP3/MP4 players). This breakout board makes it easy to add a TRRS jack to your prototype or project by breaking out each conductor to a standard 0.1" spaced header.
connectors are the audio-style connectors that you see on some phones, MP3 players and development boards. stands for "Tip, Ring, Ring, Sleeve," which reflects the fact that, unlike a standard stereo connector, this actually has three conductors and a ground.Some devices use the extra conductor for a microphone (like hands-free headsets) or to carry a video signal (like in some MP3/MP4 players).This breakout board makes it easy to add a jack to your prototype or project by breaking out each conductor to a standard.
Products with electrical plugs are designed for use in the US. Outlets and voltage differ internationally and this product may require an adapter or converter for use in your destination. Please check compatibility before purchasing.
Connectors are the audio-style connectors that you see on some phones, MP3 players and development boards. TRRS stands for “Tip, Ring, Ring, Sleeve,” which reflects the fact that, this connector has three signal connections and a ground.
Some devices use the extra conductor for a microphone (like hands-free headsets) or to carry a video signal (like in some MP3/MP4 players). This breakout board makes it easy to add a TRRS jack to your prototype or project
by breaking out each conductor to a standard
Read Also:
How the Stereo Audio Breakout Board Work:
The TRRS 3.5mm Audio Jack Breakout Board Module is an ideal solution for your audio-related experiments, comes in handy when you have an audio source on a 3.5mm Jack, and you wish to break down each component (L+R+MIC+GROUND) of the incoming signal and allows you to experiment with them over a standard 2.54mm pitch connector. TRRS stands for Tip, Ring1, Ring2, Sleeve. Apart from normal audio applications, this kind of connector could be used for microphone or video signals also. Grab one of these for your upcoming audio exA breakout board is used to connect a ribbon for cable to a breadboard, allowing larger circuits to be prototyped more easily. The two rows of pins on the breakout board should go on either side of the central divide on the breadboard: Breakout board clipped in place on a breadboard.periment.
A breakout board is used to connect a ribbon for cable to a breadboard, allowing larger circuits to be prototyped more easily. The two rows of pins on the breakout board should go on either side of the central divide on the breadboard: Breakout board clipped in place on a breadboard.
Tip-Ring-Ring-Sleeve style audio cables are often used for situations where you want stereo audio and then an extra contact for microphone input. For example, headsets for cell phones. Also called Tip Ring Ring (TRRS) jacks for short, they are also handy if you happen to want to use common audio cables for low-speed data transmission with power, ground, and 2 data lines. Tip-Ring-Ring-Sleeve style audio cables are often used for situations where you want stereo audio and then an extra contact for microphone input. For example, headsets for cell phones. Also called Tip Ring Ring (TRRS) jacks for short, they are also handy if you happen to want to use common audio cables for low-speed data transmission with power, ground, and 2 data lines.
Frequently Asked Questions
What is the function of the breakout board?
A breakout board is used to connect a ribbon for the cable to a breadboard, allowing larger circuits to be prototyped more easily. The two rows of pins on the breakout board should go on either side of the central divide on the breadboard: Breakout board clipped in place on a breadboard.
What is a breakout module?
The Signal Breakout Module also provides the capability for a second remote display through a fiber optic output connection. The packed data that is output on the fiber optic connection could be converted to an electrical signal at a remote location, using a FORT Module.
What is a breakout module?
The Signal Breakout Module also provides the capability for a second remote display through a fiber optic output connection. The packed data which is output on the fiber optic connection could be converted to an electrical signal at a remote location, using a FORT Module.
What is the breakout process?
The break-out process serves to perform the disconnecting of joints to allow for the removal of joints or other components from the drill string.
What is breakout testing?
A Citrix Breakout Test identifies ways in which a user of your Citrix environment may be able to access functionality on the Citrix server and surrounding systems that they are not intended to access. Citrix environments could be complex – easier to get working than they are to get working securely.
